127 SERIES POLELINE HARDWARE
General poleline hardware components, organized into 46 specific categories — guy fittings, cable guards by material, crossarms, ground rods, racks, clamps, brackets, and connectors — for transmission and distribution construction.
POLELINE HARDWARE
MASTER PRODUCT LINE
// GUY THIMBLES & HOOKS
Guy thimbles and guy hooks for terminating and mounting guy strand at anchor rods and pole attachment points.

// GUY WIRE CLAMPS
2-bolt and 3-bolt guy wire clamps in 1/4" through 3/4" sizes for securing guy strand terminations.
// GUY STRUT FITTINGS
Guy strut pole plates and fitting caps for anchoring guy struts to poles under 2-1/2" and 3-wire configurations.
// GUY SPREADERS & SLEEVES
Complete guy spreader assemblies and guy serve sleeves for multi-wire guying configurations.
// STEEL CABLE GUARDS
Straight steel cable guards from 3/4" to 4-1/4", protecting riser and crossarm cable runs from abrasion.
// ALUMINUM CABLE GUARDS
Lightweight aluminum cable guards from 1-1/4" to 4-1/4" for the same protection with better corrosion resistance.
// FLARED CABLE GUARDS
Flared-end steel and aluminum cable guards for smooth cable transitions at riser and mast entry points.
// THROAT CLIPS
Aluminum throat clips in 2-1/4" to 3-3/4" for securing cable guard sections in place.
// CROSSARMS
Wood, steel, hollow steel, and fiberglass deadend crossarms for primary line construction.
// CROSSARM BRACES
34" and 36" crossarm braces for reinforcing crossarm-to-pole connections.
// CROSSARM PINS & INSULATOR BRACKETS
Threaded steel crossarm pins and angle insulator mounting brackets for crossarm-mounted insulators.
// POLE TOP PINS
Threaded pole top pins in 18" and 24" lengths, plus angle-top and short-shank variants.
// POLE TOP BRACKETS
Galvanized pole top mounting brackets and pole top extension brackets for insulator and hardware attachment.
// GROUND RODS
Copper and galvanized steel ground rods in 3/4" diameter, 6', 8', and 10' lengths.
// GROUND PLATES & GRADIENT MATS
10"x16" ground plates and 6'x4' gradient mats, with and without connectors.
// GROUND CONNECTORS & BONDING CLAMPS
Bronze bonding clamps, ground rod connectors, steel-to-steel ground clamps, and pole grounding discs.
// SECONDARY RACKS
Spool racks and mast racks for secondary conductor and service drop support, sized 100A to 200A.
// CLEVIS HARDWARE
Double straight, twisted, single-point channel, spool, flat, thimble-eye clevises, and yoke strain plate.
// SUSPENSION CLAMPS
3-bolt straight and angle suspension clamps, plus curved messenger clamps.
// BEAR PAW MESSENGER CLAMPS
Bear paw style messenger clamps for neutral conductor support on concrete or steel structures.
// SWING-AWAY & DEADEND CLAMPS
2-bolt swing-away clamps for #6-2/0 ACSR and side-opening deadend clamps for #4-556 conductor range.
// FIGURE-8 SPAN CLAMPS
Figure-8 profile span clamps, straight and twisted 90 degree, for aerial cable crossovers.
// DROP WIRE CLAMPS & HOOKS
B-drop wire clamps, wire drop hooks, and wedge-type drop wire clamps.
// SPAN & LASHING CLAMPS
Lashing clamps, Q-span drop clamps, aluminum crossover span clamps, and multi-drop span clamps.
// TRIPLEX SPREADERS (WITH INSULATOR)
Triplex spreader hardware with insulator included, plus the insulator-only replacement part.
// TRIPLEX SPREADER BRACKET HARDWARE
Triplex spreader brackets and bolt kits without insulator, in 10", 12" and 14" configurations.
// TRIPLEX STAND-OFF & SECONDARY SPREADERS
Triplex stand-off bracket assemblies and Hendrix-style secondary spreader brackets.
// STAND-OFF SIDE POST BRACKETS
9" and 18" stand-off side post brackets, including the raised side plate variant.
// TTC WALL & UNISTRUT MOUNT BRACKETS
TTC bracket line for wall mounting and unistrut mounting applications, standard and galvanized.
// TTC DOUBLE-END, DEAD-END & ANCHOR BRACKETS
TTC double-end brackets, single dead-end brackets, and auger anchor brackets.
// TTC CAP & POST BRACKETS
TTC cap and post brackets, standard and galvanized.
// CUTOUT & SWITCH BRACKETS
Single-phase switch and cutout mounting brackets, plus the 14-4kV 100A overhead pole-top cutout.
// ARRESTER BRACKETS (GENERAL)
Lightning arrestor brackets, switch/arrestor combination brackets, and transformer tank arrester mounts.
// 3-PHASE ARRESTER & SWITCH BRACKETS
Three-phase intermediate arrester brackets, distribution cutout/arrester equipment mounts, and 3-phase switch brackets.
// TRANSFORMER & METER HARDWARE
Heavy-duty transformer mounting adaptors, 100A meter socket jumper bars, and meter disconnect sleeve sockets.

// EYE NUTS
Oval and thimble eye nuts in 5/8" and 3/4" for guy strand and rigging attachment.
// STRAIN EYES & EYEBOLTS
Angle strain eyes and Crosby-rated eyebolts for high-load rigging and guy attachment points.
// D-RING BOLT EYES
Bolt eye D-rings in two hole sizes for hardware and rigging attachment.
// KELLEMS GRIPS
Woven-mesh Kellems-style support and pulling grips for cable strain relief.
// PLATFORMS & ENCLOSURES
Hot-dip galvanized pole platforms, heavy-duty enclosures, and handwell covers.
// BANDING & SUPPORT BRACKETS
Banding brackets, epoxy rod drop lead rest brackets, anti-rotation bars, pole thrust fittings, jumper holding studs.
// RISERWAY & CABLE POSITIONING
Single riserway channel, cable positioners, plastic cable spacers, and the ball socket tongue fitting.
// SWITCH ACCESSORIES
Single-phase switch brackets, VBM vacuum switch plugs, and related switchgear accessory hardware.
// PIGTAIL CONNECTORS
NEMA-style and 350 MCM pigtail connectors for transformer and equipment lead connections.
// CORNER BRACKETS & FLAG ARMS
Corner mounting brackets and hi-level flag arm (flagram) hardware.
// CABLE SUPPORT & LASHING STRAPS
Cable support and lashing straps for securing communications and messenger cable to strand.
